📞 +1 877-742-2878

FREE SHIPPING ON QUALIFYING ITEMS

Oberdorfer N201D-A90 Rubber Impeller Pump and Motor

SKU
N201D-A90
   
Oberdorfer N201D-A90, max flow 7 gpm, inlet size 3/8 in, Lip Seal seal type, 39 ft max head, 2300 rpm (motor), seal Buna, Neoprene impeller.
Burt Process is an AUTHORIZED DISTRIBUTOR of this product.

OUT OF STOCK

Product images shown are for illustration purposes only 
and may not be an exact representation.

Notes OBERDORFER N201D-A90 FLEXI IMPELLER PUMP & MOTOR
Weight (lbs) 6
  • OVERVIEW
  • SPECIFICATIONS
  • DOCUMENTS
  • DOCUMENTATION
  • RELATED PRODUCTS
  • SIMILAR PRODUCTS
  • REVIEWS
  • VIDEO
  • These Rubber Impeller pumps are made of high quality bronze of maximum corrosion resistance. All shafts consist of stainless steel grade 303. Top of the line models have ball bearings and mechanical seals while others have bronze or carbon bearings and lip type seals. Impellers are made of Neoprene Rubber. Nitrile impellers are available as an option. Flexible blades on the periphery of the impeller provide the pumping action. While the impeller rotates the liquid between the blades is continuously squeezed out into the discharge port by a machined in cam located inside the pump chamber.

    To maintain the pump longer, the impeller must be replaced if it is worn out or has been damaged by debris or by running the pump dry. Symptoms of a defective impeller are low pumping pressure and low flow. To replace the impeller remove screws and cover. Pull out the impeller with needle nose pliers or two screwdrivers. Be careful not to dent the pumping chamber with these tools. When inserting new impeller, line up the flat in impeller with the flat in the shaft. Use oil on shaft and avoid forcing the impeller onto the shaft. The impeller should also be removed for storage periods to prevent the blades from taking a permanent set.DO NOT RUN DRY- Rubber impellers generate high rubbing friction unless lubricated by the liquid being pumped. Lack of liquid will cause impeller to burn up.

    FEATURES
    • Pipe Size 3/8
    • Compact Size
    • Bronze Construction - Corrosion Resistance
    • Nitrile Lip Seal
    • Large Vent Openings Separate Pump Motor
    • Stainless Steel Motor Shaft
    • Motor Shaft Slinger Protects Motor Bearings
    • Rubber Motor Grommets for Noise Isolation
    • Impeller and Cam Easily Replaced
    • Garden Hose Threads (External) Pipe Threads (Internal) for Port Connections
    • Available with 12, 24 and 32 volt D.C. Motor Drive
    • Neoprene Impeller Standard (optional Nitrile Impeller - 04)
    • For Close Coupled AC Motor units, see Models 211D and 211M
    • Marine uses include Bilge, Washdown, Baitwell and General Transfer
    DRIVE

    Motor drive is clockwise facing pump end. Liquid flow direction is right to left facing pump end. Correct D.C. voltage must be supplied to motor - 12, 24 or 32 volts as specified on motor name plate.

    Horizontal motor mountings - including sidewall mountings are recommended. The pump can be mounted in any of four positions 90o apart. Two screws attach pump to motor.

    LIQUIDS TEMPERATURES

    Liquids compatible with neoprene can be pumped including fresh and salt water solutions and mild chemicals. Do not pump severe solvents or acids. When possible, flush pump with fresh water after each usage. Nitrile impellers can handle oil, contaminated water and kerosene at reduced impeller service life.

    Extremes of cold and heat will affect impeller life. Limits of 40oto 180oF should be observed. Do not allow liquid in pump to freeze. Drain pump by loosening cover screws. Use methyl alcohol based anti-freeze compounds such as Zerex, Shell Zone, Pyro Permanent, Permagard, and Dowgard. Rubber impeller pumps are not suitable for pumping gasoline or solvents

    SUCTION LIFT

    Suction lift of 3 ft. is possible when impeller is wet. Suction lines must be air tight in order for pump to self-prime. A foot valve at the beginning of suction line is recommended.