📞 +1 877-742-2878

FREE SHIPPING ON QUALIFYING ITEMS

Oberdorfer 815B Centrifugal Pump, NO MOTOR

SKU
815B
   
Oberdorfer 815B, max flow 94 gpm, inlet size 1-1/2 in, NPT inlet/outlet connection type, 100 ft max head, 3450 rpm (motor), 1-1/4 in outlet size. Motor NOT Included
Burt Process is an AUTHORIZED DISTRIBUTOR of this product.

OUT OF STOCK

Product images shown are for illustration purposes only 
and may not be an exact representation.

Notes OBERDORFER 815B BRONZE CENTRIFUGAL CLOSE COUPLED PUMP with Mech Seal and Max Flow of 94 GPM.
Weight (lbs) 24
  • OVERVIEW
  • SPECIFICATIONS
  • DOCUMENTS
  • DOCUMENTATION
  • RELATED PRODUCTS
  • SIMILAR PRODUCTS
  • REVIEWS
  • VIDEO
  • This close coupled centrifugal pump uses a mechanical type shaft seal with a Nitrile rubber element. It is suitable for water, oils, and some mild solvents. It is limited to 212o F. fluoroelastomer seals and polytetrafluoroethylene (PTFE) seals are available for severe solvents, difficult chemicals, and elevated temperatures. The impeller is attached directly to the motor shaft. This pump can handle small impurities in the liquid. The flow of a centrifugal pump can be conveniently controlled by a throttling valve in the discharge line without the need for a relief valve. In centrifugal pumps, the horsepower demand will decrease as the pressure increases. Maximum horsepower occurs with a wide open discharge.

    FEATURES
    • Bronze Construction
    • Stainless Steel Shaft
    • Carbon Face Mechanical Pump Seals - Nitrile STD
    • fluoroelastomer (S10) or Polytetrafluoroethylene (S11) Pump Seals Available for Solvent Transfer
    • Field convertible to pedestal drive model
    • Will Handle Contaminated Liquids
    • Extremely Quiet
    • Pump-heads only easily field mounted to standard footless C flange motors
    • Keyless impeller option (815B-07)
    • O-Ring housing seal eliminates gasket problems
    • Hydraulic motor adapter available
    DRIVE

    This close-coupled pump uses a standard NEMA 56C motor with no base. Single phase motors are non-reversible and are wired for the proper pump rotation which is counter-clockwise looking at inlet end of pump. See the dimensional drawing. Three phase motors must be checked out for proper rotation when pump is installed. Interchanging of any 2 wires in a 3-phase system will reverse motor rotation.

    LIQUIDS TEMPERATURES

    The special pump alloys used provide corrosion resistance to many liquids including water, water solutions, and a wide range of commercial chemicals. Questions as to the chemical compatibility of special liquids should be referred to the factory.

    Viscous liquids with a maximum viscosity of 2000 Saybolt Seconds Universal can be pumped. However, when pumping viscous liquids as compared with water, a reduction in flow and pressure occurs and the required horsepower rate increases. Liquids heavier than water require additional horsepower in direct proportion to the increase in specific gravity. Liquids contaminated with small solids or abrasives can be handled, but a reduction in mechanical seal life must be expected. The pump uses a mechanical type shaft seal with a nitrile rubber element. It is suitable for water, oils, and some mild solvents and it is limited to 212o F. fluoroelastomer seals and Polytetrafluoroethylene (PTFE) seals are available for severe solvents, difficult chemicals, and elevated temperatures.

    SUCTION LIFT

    These centrifugal pumps are not self-priming. They must be installed below the liquid level so that the liquid flows to the pump by gravity (flooded suction). However, if a foot valve is used at the beginning of the suction line, and all air is bled from the pump by manual priming, the pump will lift on the suction side up to 15 feet. Such a system relies entirely on the non-leaking foot valve for starting capability.